RuggedCom Switch RSG2100P Manuel d'utilisateur

RuggedSwitch® RSG2100P Modular Power over Ethernet Managed Ethernet Switch Installation Guide August 14, 2008 www.ruggedcom.com RuggedCom

4 Installation 4.1 Mounting The RSG2000 series of products have been designed with maximum mounting and display flexibility. Customers can order a

4.1.1 Rack Mounting Figure 3: RSG2000 Series 19” Rack Mount Adapters Figure 4: Rack mount adapter mounting location The RSG2000 series family of

4.1.2 Panel and DIN Rail Mounting The RSG2000 series products can be ordered as a Panel/DIN mount chassis. Both options involve the use of the pane

4.2 Power Supply Wiring and Grounding Figure 6: RSG2000 Series Philips Screw Terminal Block Philips Screw Terminal without CoverPhilips Screw Termin

The RSG2100P can be equipped with either a Philips Screw Terminal Block or a Phoenix Plug Terminal Block. The Philips Screw Terminal Block has Philip

4.2.1 AC Power Supply (PS1) Wiring Example Figure 9: AC (PS1) & 48VDC (PS2) power supply wiring examples NOTES: 1. 100-240VAC rated equipment

4.2.2 DC Power Supply (PS1) Wiring Example Figure 10: DC (PS1) & 48VDC (PS2) power supply wiring examples NOTES: 1. 88-300VDC rated equipment

4.3 Dielectric Strength (HIPOT) Testing For dielectric strength (HIPOT) testing in the field, users must remove the metal jumper located on terminal

4.4 Failsafe Alarm Relay Wiring The “Failsafe” output relay is provided to signal critical error conditions that may occur on the RSG2000 series swi

4.5 Console Port Wiring A RS232 console port for configuration and management of the device is located on the LED display module shown in Figure 13

Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Clas

5 Ethernet Ports Each Ethernet module is equipped with two LEDs that indicate link/activity status information. The LED will be solid for ports wi

10/100BaseTx Pin-out Pin Description 1 RX + 2 RX - 3 TX + 6 TX - 4, 5, 7, 9 NC Table 5: RJ45 Ethernet pin-out assignment 5.1.2 Data and P

5.2 Fiber Optic Ports Depending on the order code of the product, the RSG2000 series products can be equipped with several different types of fiber

Figure 21: 100FX / 1000LX ST connector Figure 22: 1000LX GBIC Module and SC connector Figure 23: 1000LX SFP (mini-GBIC) Module and LC connector

5.2.1 Gigabit Ethernet 1000Base-Tx Cabling Recommendations The IEEE 802.3ab Gigabit Ethernet standard defines 1000Mbit/s Ethernet communications ov

5.2.2 Pluggable optics – Installation, removal, and precautions The RSG2000 series of products can be ordered with pluggable optic form factors such

5.2.2.2 GBIC Module Removal GBIC Modules have two locking latches on either side of the module shown in Figure 25. To remove GBIC module, disconnect

6 Technical Specifications 6.1 Power Supply Specifications Input Range Max. Power Consumption3 Power Supply Type (PS1) Min Max Fuse Rating 10/100

6.3 Networking Standards Supported Parameter 10Mbps Ports 100Mbps Ports 1000Mbps Ports Notes IEEE 802.3 9 10BaseT / 10BaseFL IEEE 802.3u 9 1

6.4 Twisted-Pair Port Specifications Parameter Specification Notes Speed 10/100 Mbps Auto-negotiating Duplex FDX / HDX Auto-negotiating Cable-Ty

Table of Contents 1 ... 4 Table o

6.5 Fiber Optical Specifications The following sections detail fiber optical specifications on ports that can be ordered with the RSG2000 series Eth

6.5.1 Fast Ethernet (10/100 Mbps) Optical Specifications The dual-port fast Ethernet optical specifications for RSG2100P ports 1-8 and 13-20 are sho

6.5.2 Gigabit Ethernet (1000 Mbps) Optical Specifications For maximum flexibility RuggedCom Inc. offers a number of different transceiver choices fo

NOTES: 1. Maximum segment length is greatly dependent on factors such as fiber quality, and number of patches and splices. Please consult RuggedCo

6.6 Type Test Specifications Electrical Safety Levels Comments Dielectric Withstand 2 kV rms for 1 minute ANSI/IEEE C37.90 (1989) IEC 60255-5 (Sec

6.8 Mechanical Specifications Parameter Value Comments Dimensions 18.29 x 10.17 x 1.74 inches (464,57) x (258,32) x (44,20) mm (Length x Widt

36 © 2008 RuggedCom Inc. All rights reserved Rev105 7 Agency Approvals Agency Standards Comments CSA CSA C22.2 No. 60950, UL 60950 Approved

1 Table of Figures Figure 1: RSG2000 Series LED Display Panel ... 8 Fig

Table 12: Twisted-Pair Port Specifications...29 Table 13: Fast Ethe

3 Product Overview 3.1 Functional Overview The RuggedSwitch® RSG2100P is an industrially hardened, Power Over Ethernet (PoE) enabled, fully manage

• VLAN (802.1q) to segregate and secure network traffic • Radius centralized password management • SNMPv3 encrypted authentication and access secur

3.3 Display Panel Description The RSG2000 series products are equipped with a versatile display panel, shown in Figure 1, which is designed to provi

The port-based LEDs can be cycled between three display modes: Status, Duplex, and Speed. Pushing the mode button causes the display mode to be cycl